l-1 rev.: 0/2016 www.recom-power.com 4 watt constant voltage single output ac/dc converter features led driver ? 4w ac-dc class ii led power supply ? 12v and 24v constant voltage output ? fully protected (olp, scp, ocp, otp) ? low standby power, erp conform ? ip65 (suitable for dry and damp locations) ? low cost ? ce, cb, enec, csa and ul8750 certifed. ? wired connections for independent or built-in use racv04 description these constant voltage led drivers have been designed for cost-sensitive applications. the selv outputs are suitable for built-in power-supply led luminaires. their low profle design allows them to be invisibly built into furniture, discreetly mounted under shelves or integrated in space-restricted applications such as coving lighting, strip lighting or troffer lighting systems. the power supplies are short circuit and overload protected and come with a full 3-year warranty. selection guide part nom. input input output output effciency output number voltage current voltage current range typ. power max. [vac] [ma] [vdc] [ma] [%] [w] RACV04-12 115/230 100 12 0-330 75 4 racv04-24 115/230 100 24 0-170 75 4 3 y e a r w a r r a n t y 3 basic characteristics parameter condition min. typ. max. input voltage range 90vac 230vac 264vac inrush current 11a start-up time 500ms input frequency range 47hz 63hz no load power consumption 0.5w power factor full load, 230vac 0.40 internal operating frequency full load 64khz output ripple voltage (1) 12vdc 24vdc 120mvp-p 240mvp-p specifcations (measured @ ta= 25c, 240vac and rated load) all led drivers may not be used without a load. they must be switched on the primary side only. noncompliance may damage the led or reduce its lifetime. regulations parameter condition value output voltage accuracy 5% max. line regulation 5% max. load regulation 5% max. protection parameter condition value input fuse external fuse is recommended 0.22 w fusible resistor open circuit protection (ocp) auto recovery after fault condition is removed over load protection (olp) auto recovery after fault condition is removed over voltage protection (ovp) auto recovery after fault condition is removed continued on next page notes: note1: measured at 20mhz bw using 0.1f & 47f parallel capacitor. ul8750 certifed csa c22.2 no. 250.13 certifed iec62384 certifed en55015 compliant cb report erp compliant
over temperature protection (otp) 110c tcase auto recovery after fault condition is removed isolation voltage i/p to o/p 3.75kvac / 1 minute isolation resistance 100m w ac/dc converter l-2 rev.: 0/2016 www.recom-power.com specifcations (measured @ ta= 25c, 240vac and rated load) racv04 series environmental parameter condition value operating temperature range -20c to +50c, ambient maximum case temperature +79c operating altitude 2000m operating humidity 5% to 85% rh, non condensing ip rating ip65 pollution degree pd2 design lifetime 30 x 103 hours derating graph -20 60 50 40 30 20 10 0 -10 0 20 40 60 80 100 ambient temperature [c] output current [%] maximum loading of automatic circuit breakers circuit breaker circuit breaker current typ 10a 16a 20a 25a b 17 28 35 44 c 27 59 74 92 @ 230vac, 1ohm, 90 phase angle and max. load safety and certifications certifcate type report number standard etl standard for led equipment for use in lighting products 160428123gzu-001 ul8750, 2nd edition, 2015 led equipment for lighting applications csa c22.2 no. 250.13, 2014 lamp controlgear general requirments for safety (cb scheme) 307649 + 307650 iec61347-1, 2nd edition, 2012 en61347-1, 2nd edition, 2013 lamp controlgear particular requirements (cb scheme) iec/en61347-2-13, 2nd edition, 2014 d.c. or a.c. controlgears for led performance requirements (enec) 307649-1 + 307650-1 iec/en62384, 1st edition, 2009 rohs 2.1 lcs1606201548r rohs-2011/65/eu + am-2015/863 continued on next page circuit breaker circuit breaker current typ 10a 16a 20a 25a c 54 118 148 184 @ 115vac, 1ohm, 90 phase angle and max. load
dimension and physical characteristics parameter type value material case potting plastic (ul94 v-2) silicone (ul94 v-0) package dimension (lxwxh) 38.0 x 27.0 x 21.0mm package weight 40g ac/dc converter l-3 rev.: 0/2016 www.recom-power.com racv04 series specifcations (measured @ ta= 25c, 240vac and rated load) mechanical dimensions 21.0 fc 13.5 54.0 fc 48.0 27.0 38.0 8.4 1 2 3 4 101 1721 101 1721 2.2 tc 10.0 emi compliance standard / criterion equipment for general lighting purpose emc immunity requirements 307650 en61547, 2009 limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment en55015 assessment of lighting equipment related to human exposure to electromagnetic felds en62493, 2015 esd electrostatic discharge immunity test 8kv air discharge, 4kv contact discharge en61000-4-2, 2009, criteria b radiated, radio-frequency, electromagnetic feld immunity test 3v/m en61000-4-3, 2010, criteria a fast transient and burst immunity 0.5kv (dc output) 1kv (ac input) en61000-4-4, 2012, criteria b surge immunity 0.5kv (ac input) en61000-4-5, 2014, criteria c immunity to conducted disturbances, induced by radio-frequency felds 3v en61000-4-6, 2014, criteria a voltage dips and interuptions 100% reduction, 10ms 30% reduction, 200ms en61000-4-11, 2014, criteria b en61000-4-11, 2014, criteria c limits of harmonic current emissions en61000-3-2, class c, 2014 voltage fluctuations and flicker in public low-voltage systems <=16a per phase en61000-3-3, 2013 wired connection # function wire color type strands 1 vac in (n) blue ul-1007, awg18 41/0.16 2 vac in (l) brown ul-1007, awg18 41/0.16 3 led+ red ul-1007, awg18 41/0.16 4 led- black ul-1007, awg18 41/0.16 tc= case temperature measuring point fc = fxing centers tolerance: xx.x= 0.5mm xx.xx= 0.35mm
ac/dc converter l-4 rev.: 0/2016 www.recom-power.com specifcations (measured @ ta= 25c, 240vac and rated load) racv04-lp series the product information and specifcations are subject to change without prior notice. recom products are not authorized for use in safety-critical applications (such as life support) without recoms explicit written consent. a safety-critical application is defned as an application where a failure of a recom product may reasonably be expected to endanger or cause loss of life, infict bodily harm or damage property. the buyer shall indemnify and hold harmless recom, its affliated companies and its representatives against any damage claims in connection with the unauthorized use of recom products in such safety-critical applications. packaging information parameter type value packaging dimension (lxwxh) cardboard box 290.0 x 86.0 x 76.0mm packaging quantity 10pcs storage temperature range -20c to +70c storage humidity 5% - 85% rh installation and application led+ led- l n connection
|
